🌬️ Indirect Evaporative Cooler Sizer (M-Cycle)

Size Maisotsenko Cycle (M-Cycle) dew-point indirect evaporative coolers: sub-wet-bulb cooling, dew-point effectiveness, COP > 25, and zero-humidity added sensible cooling.

⚡ Fortran 90 Engine Double Precision (IEEE 754) ✓ ISO / ASME Validated

📊 Solver Telemetry ● ACTIVE

👁️ Consultations 20

⚡ Calculs faits 17

💾 Téléchargements 148 📦 Code Fortran 4.1 KB

📅 Mise en service Jun 2026

⏱️ Latence < 1 ms

🌬️ Maisotsenko Cycle Multi-Channel Dew-Point Evaporation

Real-time visual simulation: Product dry channel (sensible cooling) and counterflow wet evaporative channels

📝 Configuration & Presets

🏜️ Desert Arid (40°C / 18% RH) 🖥️ Datacenter Free-Cooling 🏢 Commercial Building DOAS 🏭 Industrial Spot Cooling

☀️ Ambient Air Climate State

Dry-Bulb Temp T_db,in [°C]:

Relative Humidity RH [%]:

📐 Airflow & M-Cycle Architecture

Supply Product Airflow [m³/h]:

Working Air Split Fraction [%]:

Dew-Point Effectiveness ε_dp:

Maisotsenko Dew-Point (M-Cycle) Formulation:
• Product Air Outlet: T_out = T_db,in − ε_dp · (T_db,in − T_dp) [°C]
• Wet-Bulb Effectiveness: ε_wb = (T_db,in − T_out) / (T_db,in − T_wb) > 100%
• Sensible Cooling (Zero Humidity Added): Q̇ = ṁ_product · c_p · (T_db,in − T_out) [kW]
• Energy Efficiency Ratio: COP > 25 (90% electricity reduction vs compressor AC).

📊 Dew-Point Cooling Results

📊 Output Summary
💾 Fortran Source

Cooled Product Supply Temperature (T_out)

18.1 °C (Zero Moisture Added)

Wet-Bulb: 23.0 °C | Dew-Point: 14.5 °C | Capacity: 26.3 kW

SUB-WET-BULB DEW-POINT COOLING (M-CYCLE SUCCESS)

Wet-Bulb Effectiveness (ε_wb) 132.5% >100% Sub-wet-bulb M-Cycle

Energy Efficiency Ratio (COP) 54.4 >85% lower energy than DX AC

Sensible Cooling Drop -19.9 °C Inlet = 38 °C

Evaporative Water Demand 24.8 L/h 35% working air fraction

📈 Product Outlet Temp Tout (°C) vs Ambient Humidity RH (%)

📊 Sensible Cooling Capacity Q (kW) vs Supply Airflow (m³/h)

=================================================================
 THERMOFLUIDCALC — M-CYCLE DEW-POINT EVAPORATIVE COOLER REPORT
=================================================================
Case Title                 : Industrial Plant High-Efficiency Spot Cooling
Ambient Air State          : Tdb = 38.0 C, RH = 25.0% (Twb = 23.0 C, Tdp = 14.5 C)
Airflow & M-Cycle Settings : Vdot = 4000 m3/h, Working Fraction = 35.0%, eps_dp = 0.85
-----------------------------------------------------------------
COOLED SUPPLY PRODUCT TEMP : 18.06 deg C (Sub-Wet-Bulb Cooling)
WET-BULB EFFECTIVENESS     : 132.5% (>100% M-Cycle Advantage)
SENSIBLE COOLING CAPACITY  : 26.29 kW
System Energy COP (EER)    : 54.4 (Ultra-High Efficiency)
Evaporative Water Demand   : 24.8 Liters/hour
Operating Regime Status    : SUB-WET-BULB DEW-POINT COOLING (M-CYCLE SUCCESS)
=================================================================

📘 Calculation Methodology & M-Cycle Standards

Maisotsenko Dew-Point Sub-Wet-Bulb Principle

By pre-cooling the working air before it enters the wet channels, the thermodynamic limit shifts from the ambient wet-bulb ($T_{wb}$) all the way to the ambient dew-point temperature ($T_{dp}$), yielding wet-bulb efficiencies exceeding $100\%$.

Sensible Cooling Without Humidity Addition

The product supply air stream never contacts the wet surface directly, delivering crisp, dehumidified-feel sensible cooling without increasing the indoor relative humidity.

Key Engineering Assumptions

Counter-flow / cross-flow M-Cycle perforated dry-to-wet channel plate stack.
Sub-wet-bulb psychrometric path with dew-point effectiveness $\epsilon_{dp} \approx 75 - 88\%$.
Widely used in desert climate HVAC, datacenter free-cooling, and hybrid DOAS rooftop units.

ThermoFluidCalc Engineering Report